Search This Supplers Products:Mold making Silicone rubberSilicone RubberLiquid Silicone rubberMolding Silicone RubberSilicone OilPad Silicone rubber
US $11.28200 - 40,000 kilogram
US $8.8840,001 - 999,999 kilogram
Paramtents
color any
MOQ 200KG
Sample Available
Application mold making
Payment T/T L/C Western union
Package 25kg/drum 200kg/drum
Features Liquid
Port shenzhen
HS Code 39100000
Certifications RoHS, MSDS, SGS, ISO9001:2000
Packging & Delivery
Min Order200 kilogram
Briefing
Detailed
Silicone mold making rubber for architectural plaster molds
1.Mainly application of Silicone mold making rubber for architectural plaster molds
Silicone mold making rubber is a two part silicone rubber and curing with tin catalyst. As with a low viscosity,high tear strength and excellent duplication times,it's widely used for concrete casting,cement products casting,making molds for artificial stone,concrete crafts,cement crafts,GRC/GPR decorations,concrete statues and garden statues ect.
2.Features of silicone mold making rubber for architectural plaster molds
Good cut-growth resistance
High durometer hardness
Low shrinkage
Easy release
Room temperature cure within 24 hours
Heat-accelerable cure
3.Benefits of silicone mold making rubber for architectural plaster molds
Long mold life
Highly detailed reproductions
Simplified handling
4.Technical datasheets of silicone mold making rubber rtv 638#
Model:638#
Appearance:white/red
Viscosity(cs):22000
Hardness(A):33
Tensile strength(kgf/cm)≥35-36
Elongation break(%):≥450
Retractility(%):≤0.3
Operate time(min):30
Curing time(hours):2-4
Mixing proportion of curing agent:4%
5.How to making architectural plaster molds with silicone mold making rubber?
1. Stir the base (Part A) well beofre use (except when depending on machine ).
2. Shake the catalyst container (Part B) well before use.
3. This is a 100 Part A to 4 Part B mixing ratio by weight.Weigh the desire amount of base into a clean mixing container.
4. Weight the proper amount of catalyst into the container. Mix the base and catalyst together by stirring with a stick until a uniform color is obtained. Scrape the container walls and bottom well to insure a thorough mix.
5.Though it is often unnecessary to deair the material due to its low viscosity some may choose to do so. If so,place the container into a vacuum chamber and evacuate the entrapped air from the mixture using a vacuum pump capable of achieving 29 inches of mercury vacuum.The mixture will rise, crest and then collapse in the contanier. Interruption(bumping) of the vacuum may be necessary to prevent overflowing the container. Keep the mixture under full vacuum for 2-3 minutes.
6. Bleed air slowly into the vacuum chamber. When the chamber is at atmospheric equiplibrium,remove the cover plate and take out the container.
7.Pour the deaired material slowly in a steady stream from one end of the mould so that the material flows evenly over the pattern. This should minimize emtrapment of air bubbles under the flowing material. A mold may be poured firstly over the pattern, which will also help reduce the possibility of entrapping air on the pattern and in the cured rubber.A mold release agent may be applied on the pattern first to improve release.
6.Shelf life of silicone mold making rubber
Twelve(12) months from date of shipment when stored at 250C in the original sealed packages.
7.Package style of silicone mold making rubber
Packed in clean 25kg/pail, 200kg/pail.
Any question about silicon rubber, Pls feel free to contact Christy
FAX: 086-755-89948030
Mobile: 86-189 3886 7547
Skype: christyxu911
Email: hyxj(at)szrl(dot)net
网络文化经营许可证:浙网文[2013]0268-027号|增值电信业务经营许可证:浙B2-20080224-1 2007-2024 Tradevv.com. All rights reserved.